Inverters: choosing, sizing and wiring one safely
Everything about inverters for vans, boats, cabins and home backup: types, pure versus modified sine wave, sizing for continuous load, surge and idle draw, choosing 12, 24 or 48 V, low- versus high-frequency designs, inverter-chargers, DC wiring and fusing, earthing and RCDs, installation, troubleshooting and the standards in the UK, USA and Australia.
By Michael Johnson · Updated 17 November 2026 · How we check our guides
An inverter turns battery DC into mains-style AC so you can run ordinary appliances in a van, boat, cabin or during a power cut. Picking the wrong one, or wiring it badly, is the most common cause of flat batteries, tripping, buzzing appliances and melted cables in small off-grid systems. This guide explains the types, how to size one, how to wire the DC and AC sides safely, earthing and RCDs, and the standards that apply in the UK, USA and Australia.
1. Types of inverter
| Type | What it does | Typical use |
|---|---|---|
| Plug-in / cigarette-socket | Small (100–300 W) inverter on a 12 V socket | Charging laptops in a car |
| Stand-alone inverter | Battery to AC only | Vans, boats, cabins with separate chargers |
| Inverter-charger | Inverter plus mains battery charger and automatic transfer switch | Vans, boats and caravans with hook-up or shore power; home backup |
| Off-grid hybrid / all-in-one | Inverter-charger plus solar MPPT controller(s) | Cabins and sheds; neat, but one failure takes out everything |
| Grid-tie / grid-hybrid | Synchronises with and exports to the grid | Home solar; covered in the grid-tied solar guide |
| Portable power station | Battery, charger and inverter in one box | See the portable power station guide |
2. Pure sine vs modified sine
Pure sine wave inverters make a smooth AC wave like the grid. Modified sine wave (really a stepped square wave) inverters are cheaper but cause problems:
- Motors (fridges, pumps, fans) run hotter, noisier and less efficiently, and may fail early.
- Some chargers, LED drivers, dimmers, CPAP machines, induction hobs, microwaves and audio equipment won't work properly or hum.
- Appliances with clocks or timers may run fast or slow.
Pure sine inverters are now cheap enough that a modified sine inverter only makes sense for a simple heater or tool. For anything permanent, buy pure sine.
3. Sizing: continuous, surge and idle draw
- Continuous rating: add up everything that might run at once. Choose an inverter rated at least 20–25% above that.
- Surge rating: motors and compressors need 2–7 times their running power for a fraction of a second to start. The inverter's surge rating (often 2× continuous for a few seconds) must cover the biggest start-up while other loads run.
- Idle (no-load) draw: an inverter left on with nothing running still uses power: 5–15 W for a small unit, 20–50 W for a large low-frequency one. 30 W over 24 hours is 720 Wh, a big share of a small battery. Use a power-saving (search) mode or switch it off when not needed.
| Use | Typical loads | Inverter size |
|---|---|---|
| Laptop, phone, camera charging | 50–150 W | 300–500 W |
| Van with coffee machine or hair dryer | 1,000–1,500 W | 1,600–2,000 W |
| Van or boat with induction hob or microwave | 1,500–2,500 W | 2,500–3,000 W at 24 V or a large 12 V unit |
| Cabin with fridge, pump, tools | 1,500–3,000 W; surges 5,000 W+ | 3,000–5,000 W low-frequency, 24 or 48 V |
| Home backup, essential circuits | 1,000–3,000 W | 3,000–5,000 W inverter-charger |
Find appliance figures in the appliance wattage chart and size the inverter with the inverter size calculator.
Battery current
Your battery must be able to supply that current: check its BMS continuous rating. A 100 Ah lithium battery with a 100 A BMS can't run a 2,000 W inverter at full power. Work it out with the inverter battery current calculator.
4. 12, 24 or 48 V?
| Inverter size | Suggested battery voltage | Current at full load |
|---|---|---|
| Up to 1,500 W | 12 V | Up to about 140 A |
| 1,500–3,000 W | 24 V (12 V possible with very short, heavy cables) | 70–140 A at 24 V |
| 3,000 W and above | 48 V | Up to 70 A at 48 V for 3 kW |
In vehicles, 12 V is convenient because everything else is 12 V. A 24 V or 48 V house battery with a DC-DC converter for 12 V loads is the usual answer for large inverters.
5. Low-frequency vs high-frequency
| Low-frequency (transformer) | High-frequency (switch-mode) | |
|---|---|---|
| Weight | Heavy (a 3 kW unit can weigh 20–30 kg) | Light (3–8 kg for 3 kW) |
| Surge capability | High: often 3× for several seconds | Moderate: often 2× for a fraction of a second to a few seconds |
| Idle draw | Higher | Lower |
| Best for | Pumps, compressors, workshop tools, cabins | Vans, boats and electronics |
6. Inverter-chargers and transfer switching
An inverter-charger has an internal transfer relay. When shore power, hook-up or a generator is connected, it passes that supply through to your AC circuits and charges the battery. When the supply disappears, it switches to inverting in about 10–20 ms, fast enough that most computers don't notice.
- Power assist / PowerBoost lets the inverter top up a weak supply (for example a 6 A campsite hook-up or small generator) from the battery.
- Input current limit: set it to the hook-up's rating so the charger and loads don't trip the site breaker.
- Charge profile: set to your battery chemistry. Lithium needs no equalisation and usually no float or a low float.
- Earth relay: many inverter-chargers connect neutral to earth inside the unit when inverting and open that link when on shore power (section 8).
Never connect an inverter's output to a building's wiring through a plug (a "suicide lead"). It can back-feed the grid and electrocute someone. Use a proper changeover switch or a listed transfer switch; see the home backup power guide.
7. Wiring the DC side
- Fuse first: a fuse or breaker within about 300 mm (12 in) of the battery positive. Lithium batteries can deliver thousands of amps into a short, so use a fuse with enough breaking capacity: Class T, or MRBF on the terminal for smaller systems. ABYC E-11's 2025 revision gives default figures of 5,000 A interrupt capacity per 100 Ah for lithium where the maker doesn't state a short-circuit current.
- Isolator: a battery switch rated for the inverter's current.
- Cable size: rated for at least the fuse size, and thick enough to keep voltage drop to about 2%. Use the inverter cable size calculator.
- Short runs: keep the inverter within about 1–2 m of the battery; run positive and negative together.
- Lugs: use the correct-size tinned copper lugs, crimped with a proper hydraulic or ratchet crimper and covered with heat-shrink; see crimping in the campervan wiring guide.
- Pre-charge: the inverter's capacitors draw a big inrush when first connected, causing a spark and sometimes tripping the BMS. Use a pre-charge resistor or an isolator with a pre-charge function.
- Negative through the shunt: if you have a battery monitor, every negative must go through the shunt, including the inverter's.
8. The AC side, earthing and RCDs
An inverter's output is a new, separate supply. For an RCD to work, there must be a path for fault current: in most installations that means neutral connected to earth (bonded) at the inverter, and the inverter's earth connected to the vehicle chassis, boat earth or an earth electrode.
- Follow the maker's instructions. Some inverters bond neutral to earth internally when inverting; some leave it floating; inverter-chargers switch the bond with a relay. Getting this wrong either stops RCDs working or creates two neutral–earth links when on shore power.
- RCD protection: fit a 30 mA RCD or RCBOs on the inverter output circuits. Test it with the test button and, ideally, an RCD tester.
- Never connect the inverter output to a circuit that's also fed by hook-up or shore power without a changeover switch or the inverter-charger's internal relay.
- Use suitable flexible cable in vehicles and boats (not solid-core house wiring), with proper strain relief and grommets.
9. Installation: location, ventilation, interference
- Mount on a non-flammable surface in a dry, ventilated space, with the clearances the maker specifies. Inverters derate when hot.
- Not in the same sealed box as flooded lead-acid batteries (hydrogen and acid fumes). Lithium batteries can share a space if both makers allow it.
- Not in petrol engine spaces on boats unless ignition-protected.
- Secure it against movement and vibration in vehicles and boats.
- Keep it away from radios and aerials; cheap inverters can cause radio and DAB interference. Short, twisted DC cables and ferrite cores help.
- Provide a remote switch so it can be turned off easily to save idle power.
10. Rules and standards by country
United Kingdom
- Fixed AC wiring in caravans and motorhomes falls under BS 7671 Section 721, and in buildings under BS 7671 generally, including Section 551 for generating sets and Chapter 82 for prosumer installations with batteries. The IET's guidance covers inverters in caravans.
- Fitting a new circuit in a house is usually notifiable under Building Regulations Part P in England and Wales. Vans, boats and caravans aren't buildings, but an electrician should still certify fixed AC wiring.
- Caravans built to the NCC scheme follow BS EN 1648 for 12 V systems; boats on inland waterways need to pass the Boat Safety Scheme, and new boats meet the Recreational Craft Regulations with ISO 13297 for AC.
- Products must be UKCA or CE marked; many cheap online inverters aren't properly tested.
United States
- Inverters for RVs and boats should be listed to UL 458 (power converters/inverters for land vehicles and marine craft), with the marine supplement for boats. Grid-interactive inverters are listed to UL 1741.
- RVs follow NFPA 1192 and NEC Article 551, with the RVIA's low-voltage standard for 12 V; boats follow ABYC E-11 (AC and DC systems) and A-31 (battery chargers and inverters).
- Buildings follow the NEC (Article 710 for stand-alone systems, 706 for storage), with permits and inspection as required locally.
Australia
- Stand-alone power systems follow AS/NZS 4509.1; caravans and RVs with 230 V circuits follow AS/NZS 3001.2:2022, which also covers extra-low voltage batteries and inverters. Adding an inverter or upgrading to lithium counts as an alteration that must meet the current edition.
- Boats follow AS/NZS 3004.2.
- Any work on 230 V wiring, including connecting an inverter to fixed wiring, must be done by a licensed electrician. Plug-in use of an inverter (appliances plugged straight into it) isn't electrical installation work.
- Inverters must meet electrical safety requirements (RCM marking).
11. Troubleshooting
| Symptom | Likely cause | Fix |
|---|---|---|
| Low-voltage alarm when a big load starts | Voltage drop in thin or long DC cables, or a weak battery | Thicker, shorter cables; check connections are tight; test the battery |
| Inverter shuts off; lithium battery goes dead | BMS over-current trip | Check the BMS continuous and surge rating; add a second battery in parallel |
| Overload on motor start | Start-up surge exceeds the inverter's surge rating | Soft-starter, larger or low-frequency inverter |
| Hot DC terminals or lugs | Loose or poorly crimped lug | Re-crimp properly and torque to the maker's figure |
| RCD won't trip on test | No neutral–earth bond on the inverter output | Check the inverter's earthing instructions |
| Buzzing appliances | Modified sine wave output | Use a pure sine inverter |
| Flat battery overnight with nothing on | Inverter idle draw | Use search/eco mode or switch it off |
12. Frequently asked questions
What size inverter do I need?
Add up everything that could run at once and add 20–25%. Check the inverter's surge rating covers the biggest motor's start-up. For most vans 1,500–2,000 W is plenty; for a kettle or induction hob you need 2,500–3,000 W.
Do I need a pure sine wave inverter?
For almost everything, yes. Modified sine inverters can damage or upset motors, chargers, medical devices and electronics. They're only suitable for simple resistive loads like heaters.
How many batteries do I need for a 2000 W inverter?
At 12 V, a 2,000 W inverter draws about 185 A at full load, so the battery bank must be able to deliver that continuously, usually two 100 A-BMS lithium batteries in parallel or one rated 200 A. How many Ah you need depends on how long you run it.
What size fuse for an inverter?
About 1.25 times the battery current at full load, rounded up: about 300 A for 2,000 W at 12 V, or 150 A at 24 V. Use a Class T or MRBF fuse near the battery.
Does an inverter need to be earthed?
Usually yes: the inverter's earth goes to the vehicle chassis, boat earth or an earth electrode, and neutral is bonded to earth (inside the inverter or by its relay) so RCDs work. Always follow the maker's instructions.
Can I plug an inverter into my house wiring in a power cut?
Not through a plug. It can back-feed the grid and is illegal and dangerous. Use an approved changeover or transfer switch fitted by an electrician.
13. Sources
- IET, electrical installations in caravan parks, caravans and motor caravans: theiet.org
- Intertek, UL 458 power converters/inverters for land vehicles and marine craft: intertek.com
- Panbo, ABYC updated battery and electrical standards (E-11 and E-13, 2025): panbo.com
- Caravan Industry Association WA, latest electrical standards for RVs (AS/NZS 3001:2022): caravanwa.com.au
- Standards Australia, AS/NZS 4509.1 stand-alone power systems: standards.org.au
- Maritime Safety Queensland, electrical standards and licences for boats: msq.qld.gov.au
New to some of the terms? See the glossary. Not sure where to start? Try start here.