Off-grid workshop power
What tools use, cordless or corded, sizing an inverter and battery, generators for heavy tools, compressors and welders, lighting and charging, and wiring and safety.
By Michael Johnson · Updated 18 November 2026 · How we check our guides
An off-grid workshop, a shed at the bottom of the garden, a barn or a van conversion workspace all need power for tools, lighting and chargers. Power tools are demanding loads: big start-up surges, high running power and dust. This guide covers what tools use, cordless versus corded, sizing an inverter and battery, generators for heavy tools, compressors and welders, lighting and charging, wiring and safety, and running a workshop in a power cut.
1. What tools use
| Tool | Typical running power | Start-up surge |
|---|---|---|
| Drill or jigsaw | 400–800 W | Moderate |
| Angle grinder | 700–2,000 W | High |
| Circular saw | 1,200–1,800 W | High |
| Table saw, planer or mitre saw | 1,500–2,000 W+ | Very high |
| Air compressor | 1,100–2,200 W | Very high (motor starting against pressure) |
| Bench grinder | 250–500 W | Moderate |
| Wet-and-dry vacuum | 1,000–1,400 W | Moderate |
| Battery chargers | 50–300 W | Low |
Check each tool's rating plate. See the appliance wattage chart.
2. Cordless or corded?
- Cordless tools draw their energy slowly through chargers, which suit solar and small inverters.
- Stick to one battery platform so batteries are shared, and keep several charged.
- Battery packs can also power lights, fans and USB devices through adaptors. See the cordless tool batteries guide.
- Corded tools are still better for long, heavy cutting; run them from the mains or a generator.
3. Sizing an inverter and battery
- Choose an inverter with a continuous rating above the tool's running power and a surge rating that covers start-up. Low-frequency (transformer) inverters handle motor starts better.
- Use a pure sine wave inverter for tools with electronic speed control.
- At 12 V, a 2 kW tool draws over 170 A from the battery; 24 V or 48 V systems are better for workshops. See the system voltage guide.
- Heavy tools drain batteries quickly: a 1.5 kW saw for 20 minutes uses about 0.5 kWh plus losses.
- Use the inverter size calculator and the battery run time calculator.
4. Generators for heavy tools
- A generator rated well above the biggest tool's running power copes with start-up surges.
- Inverter generators give cleaner power for electronic tools.
- Run generators outdoors, away from doors and windows. See the generator guide and the generator size calculator.
- An inverter-charger with power assist can combine a small generator with the battery. See the inverter-charger guide.
5. Compressors and welders
- Compressors start against tank pressure, causing large surges. Unload valves and soft starters help. See the soft starter guide.
- Inverter welders are much easier on generators than old transformer welders; check the maker's recommended generator size.
- Both are usually best run from the mains or a generator rather than a battery system.
6. Lighting and charging
- LED strip lights on 12 V or 24 V use little power. See the LED lighting guide.
- Run tool battery chargers when the sun's out, directly from solar surplus.
- See the shed solar guide.
7. Wiring and safety
- Use RCD protection on all workshop sockets, and a proper earthing arrangement for the inverter. See the earthing guide.
- Keep batteries away from sawdust, grinding sparks and flammable finishes, in a ventilated, fire-resistant enclosure.
- Extension leads on reels should be fully unwound for heavy loads.
- Fixed mains wiring to an outbuilding must be done by a qualified electrician.
8. Frequently asked questions
What size inverter do I need for power tools?
One with a continuous rating above the tool's running watts and a surge rating to cover start-up, typically 2–3 kW for most handheld tools, more for table saws and compressors.
Can I run power tools on solar?
Cordless tools charged from solar work well. Heavy corded tools need a large battery and inverter, or a generator.
Can I run a compressor on a generator?
Yes, if the generator is large enough to handle the start-up surge; check the compressor's guidance.
9. Sources
- Victron Energy, MultiPlus-II inverter/charger datasheet: victronenergy.com
- RV PRO, Micro-Air EasyStart lets small generators start A/Cs: rv-pro.com
- California Department of Public Health, power outages and carbon monoxide poisoning: cdph.ca.gov
New to some of the terms? See the glossary. Not sure where to start? Try start here.