Home › Guides › Crimping and connectors

Crimping battery lugs and connectors

Cable and lugs, tools, crimping battery lugs step by step, small connectors and ferrules, heat shrink, tinned cable for boats, testing crimps, MC4 solar connectors, terminals and torque, and common mistakes.

By Michael Johnson · Updated 18 November 2026 · How we check our guides

Most failures in 12 V, 24 V and 48 V systems aren't the expensive parts: they're the connections. A badly crimped lug can look fine, then heat up under load, drop voltage, make an inverter cut out or, in the worst cases, start a fire. Good crimping is easy with the right tools and a bit of care. This guide covers choosing cable and lugs, tools, step-by-step crimping of battery lugs, small connectors (ring terminals, bootlace ferrules, butt connectors), heat shrink, tinned cable for boats, testing your crimps, MC4 solar connectors, terminal torque and common mistakes.

The three rules: match the lug to the cable size, use the right crimping tool and die for that size, and test every crimp with a firm pull. A crimp that moves isn't a crimp.

1. Cable and lugs

2. Tools

ToolUseNotes
Hydraulic crimper with hexagonal diesBattery and inverter cables (roughly 10–120 mm²)Best results; affordable versions are widely available
Ratchet crimper for lugsMedium cablesGood if sized correctly
Hammer crimperEmergency or occasional useInconsistent; avoid for important connections
Ratchet crimper for insulated terminalsSmall cables (0.5–6 mm²)Matching colour-coded jaws
Ferrule crimperBootlace ferrulesSquare or hexagonal crimp
Cable cuttersClean cuts on large cableDon't use pliers or a hacksaw
Heat gunHeat shrinkNot a lighter

3. Crimping battery lugs step by step

  1. Cut the cable squarely with proper cable cutters.
  2. Strip the insulation to the depth of the lug barrel. Score the insulation with a sharp knife without cutting into the copper, and don't nick or lose strands.
  3. Slide on heat shrink before fitting the lug.
  4. Insert the cable fully into the lug so the strands reach the end of the barrel, with no copper showing between the lug and insulation (or only a millimetre or two).
  5. Crimp with the correct die for the lug size. Large lugs may need two crimps along the barrel.
  6. Check the crimp: it should be firm and even. If the lug pulls off, the die was too big. If the metal is squeezed out at the die edges, the die was too small.
  7. Pull test firmly.
  8. Shrink the heat shrink over the barrel and onto the insulation.

Don't solder crimped lugs: solder can wick up the cable, making it stiff and prone to fracture where it leaves the joint, and soldered-only joints can fail if they get hot.

4. Small connectors

5. Heat shrink

6. Tinned cable and boats

7. Testing crimps

8. MC4 solar connectors

9. Terminals and torque

10. Common mistakes

11. Frequently asked questions

Should I crimp or solder battery cables?

Crimp, with the right tool and die. Soldering can make the cable stiff and prone to breaking, and soldered-only joints can fail if they get hot.

What crimper do I need for battery lugs?

A hydraulic crimper with hexagonal dies matched to the cable size gives the most reliable results.

How do I know if a crimp is good?

It shouldn't move under a firm pull, should show no stray strands, and should have almost no voltage drop under load.

12. Sources

  1. Current Connected, how to crimp battery cables: currentconnected.com
  2. iCrimp, how can I crimp battery cable lugs: icrimptools.com
  3. Haisstronica, how to crimp heavy wire lugs: haisstronica.com

New to some of the terms? See the glossary. Not sure where to start? Try start here.