Home › Guides › Boat wiring

Boat electrical wiring: 12 V DC systems and shore power

How to wire a yacht, motor boat or narrowboat safely: battery banks and switches, where fuses go and how big, marine cable and voltage drop, connections that last, routing and labelling, negatives and bonding, charging, ignition protection, shore power and electric shock drowning, corrosion, annual checks and the standards in the UK, USA and Australia.

By Michael Johnson · Updated 17 November 2026 · How we check our guides

Boat wiring lives in the harshest environment of any electrical system: salt, damp, vibration, fuel vapour and a hull that's always wet. Most boat electrical fires and failures come down to a handful of causes: unfused cables, corroded or loose connections, chafed insulation and mixed-up shore power earthing. This guide covers 12 V and 24 V DC systems and shore power on yachts, motor boats, narrowboats and small craft, with the standards in the UK, USA and Australia.

Two things on a boat can kill you electrically. Shore power faults can electrify the water around a marina (electric shock drowning), and sparks in a petrol engine space can ignite vapour. Shore-power AC work should be done by a qualified marine electrician; see section 10. Never swim near boats connected to shore power.

1. How a boat's electrics are laid out

Boat electrical system: DC distribution and shore power Fuse every positive near the battery, keep negatives on a common bus, and isolate shore power with an RCD and galvanic isolator. Start battery House bank LiFePO4 / AGM Fuse Fuse (ANL/T) Battery switches start / house / combine clearly labelled Engine starter + alternator DC distribution panel breakers per circuit voltmeter Circuits nav lights, pumps, electronics, fridge common negative bus (and DC grounding point to engine) Shore inlet 16 A / 30 A waterproof Galvanic isolator in the earth lead, or isolation transformer RCD / ELCI + main AC breaker polarity indicator AC panel sockets, charger, water heater Keep AC and DC wiring separate and labelled. Use tinned, fine-stranded marine cable, supported every 450 mm (18 in), with ignition-protected equipment in petrol engine spaces. UK: BSS/RCD (ISO 10133/13297). USA: ABYC E-11/E-13, 33 CFR 183 for builders. Australia/NZ: AS/NZS 3004.2.
A typical boat with separate start and house batteries, a DC distribution panel and an isolated shore power supply.

Most boats have:

2. Battery banks and switches

3. Fusing: where and how big

Every positive conductor needs overcurrent protection as close as practical to the battery or other power source. ABYC E-11 sets the distances most marine electricians work to:

SituationFuse or breaker within
Typical connection to a battery or bus7 in (178 mm)
Fed from a source other than a battery terminal (for example a bus or switch), sheathed along its whole length40 in (1 m)
Connected directly to a battery terminal and sheathed or enclosed along its whole length72 in (1.83 m)
Engine cranking circuitExempt from overcurrent protection (keep it short and well protected)

4. Marine cable and voltage drop

5. Connections that last

6. Routing, support and labelling

7. Negatives, DC grounding and bonding

8. Charging: alternator, solar, wind, shore

9. Ignition protection in petrol boats

In engine compartments and spaces with petrol (gasoline) engines or tanks, any electrical equipment must be ignition-protected: designed so it can't ignite fuel vapour (ISO 8846 or SAE J1171). That includes starters, alternators, bilge blowers, fuel pumps, switches and fuses. In the USA, this is a federal requirement for boat builders under 33 CFR 183 Subpart I. Diesel engine spaces don't need ignition-protected equipment, but keep it clear of fuel anyway.

Run the bilge blower for at least four minutes before starting a petrol inboard, and sniff the bilge.

10. Shore power and electric shock drowning

When a boat on shore power has a fault that leaks current into the water, people swimming nearby can be paralysed and drown. Proper shore-power installation protects against it:

Size your shore supply with the hook-up and shore power calculator.

11. Galvanic and stray-current corrosion

12. Standards and rules by country

United Kingdom

United States

Australia

13. Annual checks

  1. Check battery terminals for corrosion and tightness; clean and re-grease.
  2. Look for chafed, cracked or hot-looking cables, especially at bulkheads and in the engine space.
  3. Test the RCD/ELCI with its test button.
  4. Check navigation lights, bilge pumps and float switches work.
  5. Measure stray current with everything off.
  6. Inspect and replace anodes.
  7. Check the shore cable and plugs for damage and burnt pins.
  8. Update your wiring diagram for any changes.

14. Frequently asked questions

What wire should I use on a boat?

Tinned, fine-stranded copper cable rated for marine use, at least 105 °C in engine spaces. Never solid-core household cable.

Where should fuses go on a boat?

As close to the battery as practical: ABYC E-11 calls for 7 in (178 mm) for most connections, extended to 40 in or 72 in only where the cable is sheathed or enclosed along its whole length. The engine cranking circuit is exempt.

Do I need a galvanic isolator?

If you use shore power, a galvanic isolator (or isolation transformer) protects your underwater metals from galvanic currents coming through the shore earth from other boats. It's strongly recommended for any boat that's often plugged in.

What is electric shock drowning?

When AC current leaks into the water from a faulty boat or dock, it can paralyse swimmers, who then drown. RCD/ELCI protection on the boat and the dock, and never swimming in marinas, prevents it.

Can I do my own boat wiring?

In the UK and USA you can generally work on your own boat's DC system, but it must meet the relevant standards and pass any Boat Safety Scheme or insurance survey. Shore-power AC work should be done by a qualified electrician, and in Australia it's licensed work.

What voltage drop is acceptable on a boat?

ABYC uses 3% for critical circuits such as navigation lights, bilge pumps and electronics, and 10% for non-critical circuits like cabin lighting.

15. Sources

  1. eCFR, 33 CFR Part 183 Subpart I, electrical systems: ecfr.gov
  2. US Coast Guard, electrical compliance guidelines for boat builders: uscgboating.org
  3. Panbo, ABYC updated battery and electrical standards (E-11 and E-13, 2025): panbo.com
  4. Boat Safety Scheme, core examination checking procedures (edition 5): boatsafetyscheme.org
  5. Boat Safety Scheme, 10 most common fails: boatsafetyscheme.org
  6. Standards Australia, AS/NZS 3004.2:2014 boat installations: standards.org.au
  7. Maritime Safety Queensland, electrical standards and licences for boats: msq.qld.gov.au

New to some of the terms? See the glossary. Not sure where to start? Try start here.