How to use a multimeter
Choosing a safe meter, CAT ratings, settings and sockets, measuring DC voltage, continuity and resistance, current, clamp meters, practical tests on batteries, panels, fuses and cables, and safety rules.
By Michael Johnson · Updated 18 November 2026 · How we check our guides
A multimeter is the single most useful tool for anyone with a solar system, a campervan, a boat or a backup battery. It tells you whether a battery is charged, whether a fuse has blown, whether a cable is losing voltage, and whether a panel is producing anything at all. Used carelessly on mains or a big battery bank, though, it can also cause a short circuit, an arc flash or a shock. This guide covers choosing a safe meter, the settings and what they mean, measuring DC voltage, AC voltage, continuity, resistance and current, using a clamp meter, practical tests for batteries, solar panels, fuses and cables, and the safety rules that matter.
1. Choosing a safe meter
- Choose a meter with a CAT rating suitable for the highest-energy circuit you'll ever test (see below), from a reputable maker.
- Look for an auto-ranging meter with DC voltage, AC voltage, resistance, continuity (with a beep), diode test and DC current.
- A DC clamp meter is very useful for battery systems: it measures high currents without breaking the circuit.
- Use test leads with shrouded plugs and finger guards, and probe tips with minimal exposed metal. In the UK, HSE guidance GS38 sets out what safe test leads look like.
- Cheap meters often have overstated CAT ratings and poor internal fuses. For mains and large battery banks, it's worth buying a proper one.
2. CAT ratings explained
| Category | Where | Examples |
|---|---|---|
| CAT II | Plug-in loads | Appliances and sockets |
| CAT III | Fixed installation inside a building | Consumer units, fixed wiring, large battery and inverter systems |
| CAT IV | The origin of the supply | The meter tails and the supply cable to the house |
The higher the category, the more energy a fault can release, and the better the meter's protection against voltage spikes. A meter rated CAT III 600 V or better suits most household and off-grid work.
3. Settings and sockets
| Symbol | Measures | Leads in |
|---|---|---|
| V with a straight line (V⎓) | DC voltage: batteries, solar, 12 V circuits | COM and V |
| V with a wavy line (V~) | AC voltage: mains and inverter output | COM and V |
| Ω | Resistance | COM and V/Ω |
| Sound or diode symbol | Continuity and diodes | COM and V/Ω |
| A or mA | Current, with the meter in series | COM and the A or mA socket |
The black lead always goes in COM. The most common mistake is leaving the red lead in the A socket after measuring current, then probing a battery for voltage: this creates a dead short through the meter.
4. Measuring DC voltage
- Set the meter to DC volts.
- Put the black probe on negative and the red on positive. A minus sign on the display means the probes are reversed.
- Read the voltage. For batteries, rest them for a while with no charge or load for an accurate state-of-charge reading.
Compare readings with the battery voltage chart.
5. Continuity and resistance
- Only test continuity or resistance on circuits that are switched off and disconnected from all power sources, including batteries and capacitors.
- Continuity mode beeps when there's a low-resistance path: useful for fuses, switches, and finding which cable is which.
- Resistance readings help check heating elements, fuses and cable joints. Touch the probes together first to see the leads' own resistance.
- Large DC cables have resistance too small for most meters to measure usefully; use a voltage drop test under load instead.
6. Measuring current
- To measure current with the probes, the meter must be connected in series: the circuit is broken and the current flows through the meter.
- Most meters can only measure up to about 10 A, often for short periods. Exceeding this blows the meter's fuse or damages it.
- Never connect a meter in current mode directly across a battery.
- For anything above a few amps, use a clamp meter or a battery monitor with a shunt. See the battery monitoring guide.
7. Clamp meters
- A clamp meter measures current by sensing the magnetic field around a cable.
- Clamp around one conductor only (just the positive, or just the negative). Clamping both cancels out and reads zero.
- Many cheaper clamp meters measure AC only. For battery and solar systems, you need one that measures DC current.
- Zero the DC clamp before measuring.
8. Practical tests
| Test | How | What it tells you |
|---|---|---|
| Battery state of charge | DC volts across the terminals after resting | Approximate charge level |
| Is the charger working? | DC volts at the battery with charging on | Voltage should rise above resting voltage |
| Solar panel output | DC volts across the disconnected panel in sun (open-circuit voltage) | Should be close to the panel's Voc rating |
| Blown fuse | Continuity across the fuse, removed from the circuit | Beep: fuse is good |
| Voltage drop in a cable | DC volts between each end of the same cable, with the load running | More than a few per cent of system voltage means undersized cable or a poor joint |
| Bad connection | DC volts across a joint or terminal under load | Should be close to zero; a reading means resistance and heat |
| Inverter output | AC volts at an inverter socket (if competent) | Should be around 230 V (or 120 V) |
See the fault finding guide, the voltage drop calculator and the Ohm's law calculator.
9. Safety rules
- Inspect the meter and leads before each use. Don't use cracked probes or leads with damaged insulation.
- Check the meter works on a known live source before and after testing a circuit you think is dead ("prove, test, prove").
- Assume everything is live until proved dead.
- Keep fingers behind the probe finger guards.
- Avoid working alone on mains or large battery systems.
- Remove rings and watches near big batteries: a short through metal jewellery can cause severe burns.
- Never change the dial setting while the probes are connected.
- See the lithium battery safety guide and electrical basics.
10. Frequently asked questions
What multimeter do I need for solar and batteries?
An auto-ranging meter rated CAT III 600 V or better, ideally with a DC clamp for measuring battery and solar current safely.
Why did my multimeter blow its fuse?
Usually because the red lead was in the current (A) socket while measuring voltage, creating a short. Always check the lead sockets before probing.
How do I test a fuse with a multimeter?
Remove the fuse, set the meter to continuity and touch both ends. A beep means the fuse is good.
11. Sources
- Fluke, multimeter safety guide: fluke.com
- Fluke, FAQ: fused test leads, proving units and GS38: fluke.com
- NICEIC, when is it necessary to use fused test leads: niceic.com
New to some of the terms? See the glossary. Not sure where to start? Try start here.