Busbars, fuses and DC distribution
How DC distribution works, busbars, choosing fuses, battery switches, the order of components, negatives and shunts, small circuits, layout and labelling, and common mistakes.
By Michael Johnson · Updated 19 November 2026 · How we check our guides
As a battery system grows beyond a battery and a single inverter, the wiring at the battery end can become a tangle of lugs stacked on terminals. Busbars, fuse holders, battery switches and distribution boxes keep it tidy, safe and easy to work on. Getting the fuse type right is especially important with lithium batteries, which can deliver enormous short-circuit currents. This guide covers how DC distribution works, busbars, choosing fuses (MRBF, MEGA, ANL and Class T), battery switches, the order of components, negative distribution and shunts, sizing, layout and labelling, and common mistakes.
1. How DC distribution works
A typical system runs: battery positive → main fuse → battery switch → positive busbar → individual fuses → inverter, charge controllers, DC-DC charger and a DC fuse box. On the negative side: battery negative → shunt (battery monitor) → negative busbar → every negative cable.
2. Busbars
- A busbar is a solid copper (often tinned) bar with studs, so several cables can connect at one point instead of stacking lugs on a battery terminal.
- Choose a current rating above the total that will flow through it, and stud sizes to match your lugs (for example M8 or M10).
- Use separate positive and negative busbars, with insulated covers.
- Integrated distribution units combine busbars and fuse holders in one enclosure.
3. Choosing fuses
| Fuse | Typical use | Notes |
|---|---|---|
| Blade fuses (ATO/ATC, Maxi) | Small circuits up to about 30 A (Maxi up to about 80 A) | In fuse boxes for lights, pumps and sockets |
| MRBF (terminal fuse) | Fuse mounted directly on the battery terminal | Very close to the battery; check interrupt rating |
| MIDI and MEGA | Medium to large circuits (about 30–500 A) | Bolt-down; common in distributors |
| ANL | Large circuits | Common and cheap, but lower interrupting capacity; check suitability with lithium |
| Class T | Main fuse on large lithium banks | Very high interrupting capacity and fast acting |
- Voltage rating: fuses must be rated for DC at your system voltage; many automotive fuses are only rated to 32 V DC.
- Interrupt rating (AIC): the fuse must be able to break the battery's maximum short-circuit current. Lithium banks can exceed the rating of some common fuses.
- Size: fuse to protect the cable, not the device. See the fuse size calculator and the cable size calculator.
4. Battery switches
- A main battery isolator lets you switch everything off for maintenance or in an emergency.
- Choose a switch rated for the continuous current and DC voltage.
- Switching off with large loads running can cause arcing; turn off the inverter first.
- Some systems need a pre-charge resistor before connecting an inverter, to avoid a large spark from the inverter's capacitors.
5. The order of components
- Main fuse as close as possible to the battery positive terminal.
- Then the battery switch, then the positive busbar or distributor.
- Individual fuses for each circuit leaving the busbar.
- With several batteries in parallel, fuse each battery. See the battery banks guide.
6. Negative side and shunts
- A battery monitor shunt goes between the battery negative and everything else; only the shunt's cable should connect to the battery negative.
- All negatives, including chargers and the inverter, connect to the load side of the shunt, otherwise the monitor reads wrongly.
- See the battery monitoring guide.
7. Small circuits
- A DC fuse box (blade fuses) feeds lights, pumps, fans, USB sockets and fridges.
- Feed the fuse box from the busbar through its own appropriately sized fuse.
- See 12 V wiring basics.
8. Layout and labelling
- Mount components on a non-flammable board, close to the battery.
- Keep cables short, with the positive and negative of each circuit routed together.
- Label every fuse with its circuit and rating, and keep spare fuses nearby.
- Torque connections to the maker's figures and recheck periodically. See the crimping guide.
9. Common mistakes
- No main fuse, or one far from the battery.
- Fuses not rated for DC or for the battery's short-circuit current.
- Stacking many lugs on a battery terminal.
- Negatives bypassing the shunt.
- Busbars without covers, or rated below the current.
10. Frequently asked questions
Do I need a busbar in my battery system?
Once you have more than two or three cables per battery terminal, busbars make the system tidier, safer and easier to maintain.
What fuse should I use for a lithium battery?
One rated for DC at your system voltage, sized to protect the cable, with an interrupting capacity above the battery's short-circuit current. Large lithium banks often use Class T main fuses.
Where should the main battery fuse go?
As close as possible to the battery positive terminal.
11. Sources
- Victron Energy, Wiring Unlimited: battery bank wiring: victronenergy.fr
- Victron Energy, knowledge article: how to wire an RV battery connection (November 2026): victronenergy.com
- Victron Energy community, busbar copper directly on battery terminal: victronenergy.com
New to some of the terms? See the glossary. Not sure where to start? Try start here.