Alternator and DC-DC charging
How alternator charging works, relays and DC-DC chargers compared, smart alternators, lithium batteries, sizing a DC-DC charger, cables and fuses, ignition signals, combining with solar, boats, and common mistakes.
By Michael Johnson · Updated 18 November 2026 · How we check our guides
For vans, motorhomes, boats and overland vehicles, the engine's alternator is often the biggest source of charge for the leisure battery: a few hours' driving can put in more than a day of winter solar. But charging a second battery from the alternator isn't as simple as joining the two with a cable. Modern "smart" alternators, lithium batteries and long cable runs all cause problems for old-style split charge relays. This guide explains split charge relays, voltage-sensing relays and DC-DC chargers, smart alternators, charging lithium batteries safely, sizing the charger, cable and fuses, and protecting the alternator.
1. How alternator charging works
When the engine runs, the alternator charges the starter battery and powers the vehicle. To charge a separate leisure (house) battery, you connect it to the alternator circuit only while the engine is running, and disconnect it when the engine stops so the leisure loads can't flatten the starter battery.
2. Relays, VSRs and DC-DC chargers compared
| Method | How it works | Best for | Drawbacks |
|---|---|---|---|
| Split charge relay (ignition-triggered) | Joins the batteries when the ignition is on | Older vehicles, lead-acid leisure batteries, short cable runs | No control of voltage or current; poor with smart alternators and lithium |
| Voltage-sensitive relay (VSR) | Joins the batteries when it senses charging voltage | As above, with no ignition wire needed | Can "chatter" on and off; smart alternators may not raise voltage enough |
| DC-DC (battery-to-battery) charger | Takes alternator power and runs a proper multi-stage charge for the leisure battery | Smart alternators, lithium and AGM batteries, long cable runs | Costs more; limited to its rated current |
| Alternator-direct regulator (external regulator, second alternator) | Controls a high-output alternator for big battery banks | Boats and large expedition vehicles | Specialist installation |
3. Smart alternators
- Since around 2015, many vehicles (especially Euro 6 vans and motorhome bases) use "smart" or variable-voltage alternators that cut their output when the starter battery is full, and charge mainly when braking or decelerating, to save fuel.
- Their voltage can drop to around 12.5 V or swing up and down, so a relay or VSR may barely charge the leisure battery.
- A DC-DC charger boosts and regulates the voltage, charging the leisure battery properly whatever the alternator is doing.
- Many DC-DC chargers have a smart-alternator mode, using an ignition (D+) signal rather than voltage to know the engine is running.
- Don't try to disable a smart alternator's control system without the vehicle maker's guidance; it can upset the engine management.
4. Charging lithium batteries from an alternator
- Lithium (LiFePO₄) batteries have very low resistance and will accept a huge current from a relay connection, which can overheat cables and overwork the alternator, especially at idle in traffic.
- They also need the correct charge voltage, and many must not be charged below freezing.
- A DC-DC charger limits the current to a safe level and uses a lithium charging profile. It's effectively essential for lithium.
- Choose a charger with a low-temperature cut-off or one that talks to the battery's BMS. See the BMS guide.
5. Sizing a DC-DC charger
- Common sizes are 20, 30, 40 and 50 A, with larger models up to 70 A and beyond.
- A common guide is no more than about a third to half of the alternator's rated output, to leave enough for the vehicle and avoid overheating the alternator.
- Match it to the battery: lithium batteries can take more; lead-acid batteries are limited by their own charge acceptance.
- Think about how much you drive: a 30 A charger running for an hour adds about 30 Ah (around 380 Wh at 12.8 V), less losses.
- Use the DC-DC charger size calculator and the battery charge time calculator.
6. Cables, fuses and earths
- The input side carries more current than the output (the charger draws extra to make up for losses, and more when boosting from a low voltage), so size the input cable for the charger's maximum input current.
- Long runs from the engine bay to the back of a van need thick cable to keep voltage drop low. See the DC cable size calculator and the voltage drop calculator.
- Fit a fuse close to each battery on the positive cables (starter battery end and leisure battery end). See the fuse size calculator.
- Use a solid negative return: a dedicated negative cable is more reliable than chassis earths, especially at higher currents.
- Follow the charger's manual for cable sizes and fuse ratings.
- See 12 V wiring basics and crimping and connectors.
7. Ignition signal and engine-run detection
- Many DC-DC chargers can detect the engine running from voltage alone, but with smart alternators this can fail; an ignition or D+ signal wire is more reliable.
- Some chargers have adjustable engine-shutdown detection to stop them draining the starter battery.
- Check the starter battery isn't being drained when parked: measure its voltage after a night.
8. Combining with solar and shore power
- DC-DC chargers, solar charge controllers and mains chargers can all charge the same leisure battery; they work alongside each other.
- Some combined units (DC-DC plus MPPT) save space in small vans.
- A battery monitor shows how much each source contributes. See the battery monitoring guide.
- See the campervan wiring guide and the van solar seasons guide.
9. Boats
- Boats often use battery combiners, DC-DC chargers or external alternator regulators to charge large house banks.
- Engine-driven charging is the main winter source on many boats; long engine runs at the mooring to charge batteries are inefficient compared with a proper regulator or DC-DC setup.
- Use marine-grade, tinned cable and follow the boat standards. See the boat 12 V wiring guide.
10. Common mistakes
- Using a relay with a smart alternator or lithium battery.
- Undersized input cable, so the charger cuts back or the cable gets hot.
- Missing fuses at one end of the cable.
- Relying on a poor chassis earth.
- Fitting a charger too large for the alternator.
- Mounting the charger where it can't cool, or in the engine bay when it isn't rated for it.
11. Frequently asked questions
Do I need a DC-DC charger or a split charge relay?
Use a DC-DC charger if your vehicle has a smart alternator (most vans from about 2015) or you have a lithium leisure battery. A relay can work on older vehicles with lead-acid batteries.
What size DC-DC charger do I need?
Typically 20–50 A, kept to about a third to half of the alternator's output and matched to your battery and driving.
Can I charge a lithium battery directly from the alternator?
Not safely with a relay: lithium accepts very high current, which can overheat cables and the alternator. Use a DC-DC charger with a lithium profile.
12. Sources
- Jacksons Leisure, why choose a DC-DC charger over a split charge relay: jacksonsleisure.com
- Victron Energy, Orion-Tr Smart DC-DC charger: automatic engine shutdown detection: victronenergy.com
- Sargent, do I need to install a DC-DC charger?: sargent.zohodesk.eu
New to some of the terms? See the glossary. Not sure where to start? Try start here.