Home › Guides › Van insulation

Van insulation: materials, condensation and how to fit it

Insulation materials compared by thermal performance, how condensation forms and where the vapour control layer goes, where heat really escapes, thermal bridges and windows, and a layer-by-layer method for walls, roof and floor.

By Michael Johnson · Updated 17 November 2026 · How we check our guides

Insulation decides how warm a van, horsebox, caravan or tiny house stays in winter, how cool it stays in summer, how much diesel or battery the heater uses, and whether you wake up to dripping walls. This guide compares the materials, explains vapour barriers and condensation (the part most people get wrong), shows where heat really escapes, and gives a layer-by-layer method for walls, roof, floor and windows.

Work it out first. The heat loss calculator shows how much each change saves in watts and heater size, and the insulation R-value calculator compares materials and thicknesses.

1. Where the heat goes

Insulating a van wall: layer by layer Cross-section from outside (cold) to inside (warm). Keep insulation tight to the steel; put vapour control on the warm side. Steel skin Closed-cell foam Wool / PET fill PIR board Vapour control Batten + air gap Lining (ply) OUTSIDE cold INSIDE warm, moist air moisture is stopped at the VCL Steel skin Closed-cell foam bonded tight to steel Wool / PET fill fills cavity, no air gaps PIR board foil faced Vapour control taped joints, warm side Batten + air gap for cables Lining (ply) finish
A typical insulated wall, from the metal skin to the lining, with the vapour control layer on the warm side.

In an uninsulated panel van at 0 °C outside and 20 °C inside, heat loss can exceed 2 kW. Good insulation cuts it to 400–800 W. The biggest losses, roughly in order:

  1. Windows and the cab: single glazing and the uninsulated cab can be a third or more of the total.
  2. Thermal bridges: steel ribs and pillars that connect the cold skin to the inside.
  3. Air leaks and ventilation: draughts round doors and through the floor.
  4. Roof, walls and floor: in that order, because warm air rises.

2. Insulation materials compared

MaterialThermal conductivity (λ, W/mK)R per 25 mm (m²K/W)ProsCons
PIR / polyiso board (Celotex, Kingspan)0.0221.14Best performance per thickness; foil faces act as a vapour barrierRigid, hard to fit curves; gaps must be taped or foamed
XPS board0.029–0.0340.74–0.86Tough, moisture resistant; good for floorsRigid; lower R than PIR
Closed-cell rubber foam (Armaflex type)0.033–0.0360.69–0.76Self-adhesive, follows curves, acts as its own vapour barrier, damps soundExpensive; heavy for its R-value
Sheep's wool0.035–0.0400.63–0.71Fills cavities, handles moisture well, natural, no itchNeeds good ventilation/vapour control; check moth treatment
Polyester / recycled PET wool0.035–0.0400.63–0.71Fills cavities, doesn't absorb water, no itchCompresses if packed too tight
Thinsulate (automotive)About 0.035–0.040About 0.6–0.7Light, hydrophobic, sound damping, easy to fitExpensive
Spray foam (closed-cell)0.022–0.0280.9–1.1Seals every gap; adds stiffnessMessy, hard to undo, can trap water if poorly applied; professional job
Mineral wool / glass fibre0.032–0.0440.57–0.78CheapHolds water and sags with vibration; not recommended for vehicles
Foil bubble wrap ("reflective insulation")Very low R on its ownAbout 0.1–0.2Cheap; reflective only with an air gapLittle insulation value: use as a radiant layer, not instead of insulation

λ values are typical manufacturer figures. US R-value per inch ≈ 0.144 ÷ λ; for example PIR (λ 0.022) ≈ R-6.5 per inch.

3. Condensation and vapour control

Each person breathes out about 0.5–1 litre of water a day; cooking, showering and drying clothes add more, and gas heaters without a flue add a lot. When that moist air reaches a surface colder than its dew point, water condenses. Inside a wall, that means rust, rot and mould you can't see.

4. Layer by layer: walls, roof and floor

  1. Prepare: remove all rust, treat bare metal, and fit sound deadening (see section 8).
  2. Walls: fit closed-cell foam or cut PIR to the flat panels, bonded tight to the skin; fill deep cavities with wool or polyester; cover ribs (section 5).
  3. Roof: the most important surface. 25–50 mm of PIR or 20–30 mm of closed-cell foam, tight to the skin, joints taped.
  4. Floor: 15–25 mm of XPS or PIR between battens, with a plywood floor on top. Rubber or vinyl flooring finishes it.
  5. Vapour control: tape all foil joints with foil tape, or fit a membrane over the inside, taped to the edges and around every cable and fixing.
  6. Lining: ply, tongue-and-groove, carpet lining or panels, fixed with gaps for cables planned in advance (see the campervan wiring guide).
SurfaceTypical build-up (good)U-value (approx.)
WallSteel + 19 mm closed-cell foam + 25 mm PET wool in cavities + VCL + 6 mm ply0.8–1.2 W/m²K (allowing for ribs)
RoofSteel + 40 mm PIR (taped) + 6 mm ply0.5–0.8 W/m²K
FloorSteel + 20 mm XPS + 12 mm ply + vinyl1.0–1.3 W/m²K
Uninsulated steel panel–5–6 W/m²K

Convert between U-values and R-values with the U-value to R-value converter.

5. Thermal bridges: the metal ribs

6. Windows, doors and the cab

7. Ventilation: the other half

8. Sound deadening

9. Common mistakes

10. Rules worth knowing

11. Frequently asked questions

What is the best insulation for a campervan?

For the best warmth per millimetre, PIR board on flat areas and the roof, with closed-cell foam on ribs and curves, and polyester or wool in deep cavities. Closed-cell foam alone is easy and moisture-proof but costs more for the same warmth.

Do I need a vapour barrier in a van?

Yes, on the warm (inside) face of the insulation, with all joints taped. Foil-faced PIR and closed-cell foam act as one when joints are sealed. Never leave an air gap where moist air can reach the cold metal.

How do I stop condensation in my campervan?

Insulate fully including the ribs, fit a vapour control layer, ventilate with a roof fan, cook with lids on, use a vented diesel heater rather than an unflued gas heater, and use insulated window covers.

Is bubble foil good insulation?

On its own, no: its insulation value is very low. It only helps as a reflective layer with an air gap, in addition to proper insulation.

12. Sources

  1. Car Insulation UK, how to stop condensation in a campervan: carinsulation.co.uk
  2. Car Insulation UK, how to install a vapour barrier in your van: carinsulation.co.uk
  3. Two Wandering Soles, van insulation DIY guide: twowanderingsoles.com
  4. Build a Campervan, insulation: buildacampervan.com

New to some of the terms? See the glossary. Not sure where to start? Try start here.