Mounting solar panels
Mounting types, pitched roofs, wind and snow, flat roofs, ground and wall mounts, vans and boats, materials and corrosion, rules and insurance, and working safely.
By Michael Johnson · Updated 19 November 2026 · How we check our guides
A solar panel is a large, flat sail. Mounting it so it survives decades of gales, snow and corrosion, without letting water into the roof, matters as much as the electrical side. This guide covers the main mounting types (pitched roofs, flat roofs, ground mounts, walls, vans and boats), fixing into rafters, roof edges and wind uplift, flat-roof ballast, ventilation behind panels, corrosion, working safely at height, and the planning and building control points to check.
1. Mounting types
| Type | Suits | Notes |
|---|---|---|
| On-roof rails and hooks | Tiled and slate pitched roofs | Most common for houses |
| In-roof (integrated) | New roofs and re-roofs | Panels replace tiles; needs careful flashing |
| Ballasted or fixed frames | Flat roofs | Weight or fixings resist wind; check the roof can take the load |
| Ground mount | Gardens, fields, off-grid sites | Easy access, best angle; see the ground-mounted solar guide |
| Wall or vertical | South-facing walls, snowy sites | Good winter output; see the vertical solar guide |
| Vehicle and boat mounts | Vans, motorhomes, boats | Brackets, spoilers or bonded mounts |
2. Pitched roofs
- Roof hooks are screwed into the rafters, never only into battens or tiles. Find rafters from inside the loft and mark them.
- Tiles are notched or replaced so the hook sits flat and doesn't press on the tile below (which cracks tiles and lets water in).
- Slate roofs often use slate hooks with lead or proprietary flashing plates.
- Rails bolt to the hooks; panels are held by end clamps and mid clamps at the positions given in the panel manual.
- Leave a gap behind the panels for airflow: panels lose output as they get hotter.
- Bond or earth frames where the system design requires it. See the off-grid earthing guide.
3. Wind, snow and roof edges
- Wind uplift is strongest at roof edges, corners and ridges. Keeping panels back from edges reduces load and helps meet roofing standards.
- The number of hooks needed depends on the wind zone, roof height, exposure and snow load; mounting-system makers publish design tools for this.
- In the UK, MCS-certified installers use roof kits tested to MCS 012 for wind and fire performance.
- Heavy snow on panels can slide off in one go; think about where it will land (doorways, paths, conservatories). See the snow and roof load guide.
4. Flat roofs
- Ballasted frames use concrete blocks or trays to hold panels down without piercing the roof membrane.
- Ballast adds weight: a structural check may be needed, especially on older garage and extension roofs.
- Protect the membrane with a pad under frames, and keep drainage routes clear.
- Low tilt angles (10–15°) reduce wind loading and shading between rows, at some cost to winter output.
5. Ground and wall mounts
- Ground mounts use ground screws, concrete footings or posts; they must resist uplift and frost heave.
- Set the lowest edge high enough to clear snow, grass and splash, and keep livestock off cables.
- Wall brackets must fix into solid masonry with suitable anchors, not into render alone.
- See the tilt and orientation guide for angles.
6. Vans, caravans and boats
- Corner brackets or spoilers fixed with structural adhesive and, where suitable, through-bolts or rivnuts into the roof ribs.
- Check the roof can take the load and that fixings don't go into hidden wiring or water lines.
- Seal every hole properly and use a proper cable entry gland.
- Flexible panels can be bonded to curved roofs but run hotter and often last less long; leave an air gap if you can.
- See the campervan wiring guide.
7. Materials and corrosion
- Aluminium rails and stainless steel fixings are standard.
- Avoid direct contact between different metals in wet conditions where possible, particularly near the sea.
- Use fixings supplied with the mounting system and torque them to the stated values.
- Inspect fixings yearly, and after storms. See the solar maintenance guide.
8. Planning, building control and insurance
- Most roof-mounted solar on houses in England is permitted development, with conditions on how far panels protrude and where they go; rules differ in listed buildings, conservation areas and the other UK nations. See the solar planning guide.
- Roof work that significantly changes the load, or that's part of a wider project, may need building regulations approval.
- Tell your home insurer about solar panels.
- Connecting a grid-tied system needs notifying the network operator; see the grid-tied solar guide.
9. Working safely
- Plan the job so you spend as little time at height as possible.
- Use scaffolding with edge protection for roof work; ladders are for short access only and must be secured.
- Don't work on roofs in wind, rain or ice.
- Panels produce voltage in daylight; keep connectors covered and unconnected while mounting.
10. Frequently asked questions
Can roof hooks be fixed to the battens?
No. Hooks must be fixed into the rafters, using the fixings and spacing the mounting system specifies.
Do flat-roof solar panels need to be bolted down?
Not always: ballasted systems use weight instead. But the roof must be able to carry the extra load, and the ballast must be designed for local wind.
How far from the roof edge should panels be?
Mounting system guidance and roofing standards set edge distances; keeping clear of edges and corners reduces wind uplift.
11. Sources
- Planning Portal, solar equipment mounted on a house or building: planningportal.co.uk
- Planning Portal, stand-alone solar equipment: planningportal.co.uk
- Rentokil, pigeon-proofing solar panels: rentokil.co.uk
- Planning Portal blog, changes to permitted development rules for domestic solar: planningportal.co.uk
New to some of the terms? See the glossary. Not sure where to start? Try start here.