Common solar panel faults
Spotting a problem, common faults, checking output, testing panels, pigeons and bird mesh, storms, hail and snow, and repair, replace or claim.
By Michael Johnson · Updated 19 November 2026 · How we check our guides
Solar panels are reliable, but they're not indestructible. Over the years, some develop hot spots, cracked cells, browning, delamination, failed bypass diodes or junction box faults, and many UK roofs suffer from pigeons nesting underneath. A drop in output is often the first sign. This guide covers how to spot a problem, the common faults and what causes them, checking output and testing panels safely, birds and bird mesh, storm and hail damage, when to repair or replace, and warranty claims.
1. Spotting a problem
- Lower generation than the same month last year, allowing for weather.
- Inverter error codes, or one string producing less than another.
- Panel-level monitoring showing one panel below the rest. See the microinverters guide.
- Visible damage: cracks, discoloured patches, bubbles, burn marks or loose cables.
- Pigeon droppings, nesting material or noise under the panels.
2. Common faults
| Fault | What it is | Causes |
|---|---|---|
| Hot spots | A cell or area much hotter than the rest | Shading, dirt, bird droppings, cracked or faulty cells; can damage the panel over time |
| Micro-cracks and cracked cells | Fine cracks in cells, often invisible | Rough handling, walking on panels, snow loads, hail, thermal cycling |
| Snail trails | Dark lines across cells | Often a sign of micro-cracks with moisture reacting with materials |
| Delamination | Layers separating, bubbles or cloudiness | Manufacturing defects, heat and moisture |
| Browning or discolouration | Yellow or brown patches | Ageing of the encapsulant, UV exposure |
| Potential-induced degradation (PID) | Gradual loss of output across a string | High system voltage and humidity in some panels |
| Bypass diode failure | A third of a panel stops producing, or overheating | Lightning, overheating, age |
| Connector and junction box faults | Burnt or melted connectors, arcing | Poor crimps, mismatched connectors, water ingress |
3. Checking output
- Compare monthly totals with previous years and expected figures. See the output calculator.
- On a clear day around noon, compare strings or panels with each other.
- Clean panels if heavily soiled. See the maintenance guide.
- Check trees haven't grown into the light.
4. Testing panels
- For accessible ground or van panels, a competent person can measure open-circuit voltage and short-circuit current against the datasheet (allowing for temperature and light). See the datasheet guide and the multimeter guide.
- A thermal imaging camera, ideally used on a sunny day under load, shows hot spots, failed diodes and bad connections.
- Installers can do IV-curve tests and electroluminescence imaging to find hidden cracks.
- Always isolate before disconnecting connectors; never disconnect MC4 connectors under load.
5. Pigeons and bird mesh
- Pigeons nest in the sheltered gap under roof panels, bringing noise, mess, blocked gutters and chewed cables.
- Bird mesh fitted around the edge of the array, clipped to the panel frames (not drilled), keeps them out.
- Wild birds' active nests, eggs and young are protected by law. Fit mesh when nests aren't in use, or get advice from a pest control professional on what's allowed.
- Mesh fitting usually needs scaffolding or roof access equipment.
6. Storms, hail and snow
- After storms, check for loose panels, damaged frames, cracked glass and lifted rails.
- Cracked glass lets water in; isolate and get it replaced.
- Heavy snow loads can crack cells; don't try to clear roof panels from a ladder. See the snow and roof load guide.
- Lightning can damage diodes and inverters. See the lightning guide.
7. Repair, replace or claim
- Connectors, cables and junction box faults can often be repaired.
- Panels with cracked glass, delamination or failed cells are usually replaced; finding a matching panel can be hard for old models.
- Check the product and performance warranties, and keep monitoring records as evidence.
- Home insurance may cover storm damage. See the insurance claims guide.
8. Frequently asked questions
How do I know if a solar panel is faulty?
Look for lower output than expected, error codes, one panel underperforming on monitoring, or visible cracks, discolouration or burn marks.
What causes hot spots on solar panels?
Shading, dirt, bird droppings and damaged cells can force a cell to dissipate power as heat instead of producing it.
How do I stop pigeons nesting under solar panels?
Fit bird mesh around the array edge when nests aren't in use, using clips rather than drilling the panels.
9. Sources
- EnergySage, solar panel defects: hot spots, snail trails and more: energysage.com
- Wikipedia, photovoltaic module analysis techniques: wikipedia.org
- Expert Reviews, pigeon proofing solar panels: expertreviews.co.uk
- Rentokil, pigeon proofing solar panels: rentokil.co.uk
New to some of the terms? See the glossary. Not sure where to start? Try start here.