Pellet stoves and boilers in a power cut
Why pellet stoves need electricity, what happens in a power cut, power use, backup options, restarting safely, pellet boilers, storing pellets, and alternative heat.
By Michael Johnson · Updated 18 November 2026 · How we check our guides
Wood pellet stoves and boilers are popular in rural homes off the gas grid: they burn a renewable fuel cleanly, feed themselves automatically from a hopper, and can be controlled by a thermostat. But unlike a traditional log burner, a pellet appliance needs electricity to run its feed auger, fans, igniter and controls. In a power cut it stops heating, and in some cases smoke can leak into the room. This guide explains what happens to pellet stoves and boilers in a power cut, how to keep one running from batteries or a generator, restarting safely, and storing pellets so they stay usable.
1. Why pellet stoves need electricity
- Auger: a motorised screw feeds pellets from the hopper into the burn pot.
- Combustion (exhaust) fan: pulls air through the fire and pushes fumes up the flue.
- Room fan: blows warm air into the room (on air stoves).
- Igniter: an electric element lights the pellets.
- Control board: runs the thermostat, timer and safety sensors.
- Pump: boiler stoves and pellet boilers also need a pump to circulate water.
2. What happens in a power cut
- The auger stops, so no more pellets reach the fire, and the flame dies down within minutes.
- The exhaust fan stops; the pellets already burning smoulder. With a good flue, natural draught carries the smoke away; with a short or poorly designed flue, or worn door seals, some smoke can come into the room.
- The room fan stops, so less heat reaches the room, and the stove body can get hotter than normal.
- Boiler stoves lose their pump: water in the boiler can overheat. Systems should have a heat leak radiator or gravity circuit to dump heat safely; check yours has.
- Most stoves don't restart automatically when the power returns.
3. How much power they use
| Stage | Typical power |
|---|---|
| Ignition | About 300–500 W for 5–10 minutes |
| Running | About 50–150 W (larger ducted stoves more) |
| Standby | A few watts |
Over a day, a stove running continuously at 100 W uses about 2.4 kWh, before ignition. Check the label or manual for your model.
4. Backup power options
| Option | Runtime | Notes |
|---|---|---|
| UPS (500–1,000 VA, pure sine wave) | 20–60 minutes | Lets the stove shut down safely with fans running; won't heat for long |
| Portable power station (1–2 kWh) | About 8–20 hours at 100 W | Pure sine wave output; check it can handle the igniter surge |
| Inverter and 12 V battery bank | Depends on capacity | Battery charger needed to recharge |
| Generator | As long as fuel lasts | Use an inverter generator for clean power; outdoors only. See the generator guide |
- Pellet stove control boards can be sensitive: use a pure sine wave supply.
- Some stoves have a battery backup option from the manufacturer; ask your installer.
- Avoid starting the stove from a small battery: the igniter's surge can trip it. Light it while on mains or generator, then switch to battery.
- Use the UPS runtime calculator and the power station run time calculator.
- Never use a "suicide lead" to backfeed a house circuit. See the transfer switch guide.
5. Restarting after a power cut
- Let the stove cool down fully.
- Empty unburnt pellets from the burn pot, so they don't cause a smoky or explosive restart.
- Clear any error messages following the manual.
- Check the flue and room for smoke smell; ventilate if needed.
- Restart with a normal ignition cycle.
6. Pellet boilers and central heating
- Pellet boilers need power for the feed, fans, controls and the central heating pump.
- Some systems use a buffer (thermal store) tank that keeps hot water for hours after the boiler stops.
- Gravity circuits and heat leak radiators protect against overheating; have your installer explain how your system copes with a power cut.
- Have the system serviced yearly by a competent engineer (HETAS-registered for solid fuel).
7. Storing pellets
- Keep pellets dry: damp pellets swell, crumble and jam the auger.
- Store bags off the floor, under cover, in a ventilated space.
- Bulk pellet stores give off carbon monoxide as pellets age, especially in enclosed silos or rooms: ventilate before entering and never go into a bulk pellet store alone. Follow the supplier's safety signage.
- Buy quality-certified pellets (ENplus A1 or similar); poor pellets cause more ash and clinker.
- Keep a few weeks' supply before winter. See the fuel storage guide.
8. Alternative heat
- A traditional log burner needs no electricity. See the wood burner guide.
- Low-power heating on batteries keeps people warm. See the low-power heating guide.
- See keeping warm in a power cut.
9. Frequently asked questions
Will a pellet stove work in a power cut?
No. It needs electricity for the auger, fans and controls. It stops feeding pellets and the fire dies down.
Can I run a pellet stove on a power station?
Often yes, from a pure sine wave power station big enough for the igniter surge. At about 100 W running, a 1 kWh unit gives roughly 8 hours.
Why did my pellet stove smoke when the power went off?
The exhaust fan stopped while pellets were still burning. Check the flue design and door seals with your installer, and fit a CO alarm.
10. Sources
- Selectra, pellet stove electricity cost and power cuts: selectra.co.uk
- Anker SOLIX, how to power a pellet stove during an outage: ankersolix.com
- Harman PC45 manual, minimising smoke during loss of power: manualslib.com
New to some of the terms? See the glossary. Not sure where to start? Try start here.